- Appliance manuals and free pdf instructions. Find the user manual you need for your home appliance products and more at ManualsOnline.
- The 60–983 is an ATP1000 Alphanumeric Touchpad from Interlogix that can promote high operation while allowing for on-site installer programming.
Atp1000 touchpad/display installation instructions, Product summary, Installation
Interlogix 60–983 ATP1000 Alphanumeric Touchpad: Large 2X16 Liquid Crystal Display w/Adjustable Contrast and Brightness. Swing-Down, Removable Door. Police, Fire and Auxiliary Panic Buttons. Allows for On-Site Installer Programming. Control Concord panels with the ATP-1000 Alphanumeric programmable touchpad.
Advertising
ATP1000 Touchpad/Display Installation
Instructions
Product summary
The ATP1000 lets you control all programming and operation
of compatible security systems (see the “Specifications”
section).
The large 2-line, 16-character display provides easy to read
messages to indicate the current status of the system. The
touchpad includes police, fire, and auxiliary panic buttons that
can be activated anytime. A built-in speaker provides alarm,
status, and button-press sounds. A swing-down door reveals a
label with basic system operating commands. The door can be
removed by simply opening it past its stop point. The door can
also be reattached later if desired.
Tools and equipment needed
•
4-conductor, 22- or 18-gauge wire
•
Screwdriver
•
#6 screws and anchors (included)
•
Panhead screws for gang box installation
•
Saw or utility knife for cutting wallboard
Installation
Installation guidelines
•
Mount the touchpad in an environmentally controlled area
(32°F to 120°F/0°C to 49°C).
•
When mounting the touchpad, allow at least 3 inches
below it for the swing-down cover.
•
Do not exceed the maximum available power. See the
panel installation instructions for maximum available
power.
•
Table 1
describes the power used by the touchpad.
•
Table 2
describes the maximum wire lengths allowed
between the touchpad and the panel.
Table 1. Touchpad power usage
Current (mA)
Conditions
110
Maximum alarm current with the buzzer sounding
and the touchpad illuminated from a button press
60
Typical operation
12
Power saving mode (no panel AC power)
Table 2. Maximum touchpad wire lengths
Wire Gauge (Unshielded
or Shielded)
Max. Touchpad Wire Length
Between Touchpad and Panel
18
750 feet
22
300 feet
Installing the Mounting Plate
1. Separate the mounting plate from the touchpad by first
loosening the screw, then lift the touchpad away from the
mounting plate (see
Figure 1
).
Figure 1. Separating touchpad from mounting plate
Loosen screw,
then lift touchpad.
P/N 466–2100 • REV I • January 2011
1
Advertising
Table of contents
- Product summary
- Tools and equipment needed
- Installation
- Installation guidelines
- Installing the Mounting Plate
- Connecting the touchpad for system programming only
- Adjusting display brightness and contrast
- Changing the touchpad unit number(Concord panels with software version 1.0–1.6 only)
Popular Brands
Popular manuals
Advertising
2. For wall mounting, place the mounting plate on the wall
and mark the mounting holes (see
). Be sure to
leave a 3-inch clearance below for the touchpad door to
open.
Figure 2. Mounting hole locations
Mounting Holes
Mounting Holes
3. Insert anchors into the wall at the marked locations where
studs are not present.
4. Align the mounting plate holes with the wall or gang box
screw holes and secure the back plate using the screws
provided.
Note: Do not over tighten screws or the mounting plate
may bind and prevent the touchpad from mounting
Ge Security 60–983 Atp1000 Alphanumeric Touchpad User Manual Online
properly.
5. For wall-mount installations, cut a hole in the wall in the
wire access area of the mounting plate to pull the wiring
cable through.
Wiring the Touchpad to the Panel
1. Remove panel AC and backup battery power.
2. Run a 4-conductor, 18- to 22-gauge wire from the panel to
the touchpad location (see
3. Connect the touchpad +12V, BUS A, BUS B, and GND
terminals to the matching panel terminals (see Figure 3 for
touchpad terminal identification)
Figure 3. Touchpad wiring connections
GND
BUS B
BUS A
+12V
Attaching the Touchpad to the Mounting Plate
Align the tabs at the top of the mounting plate with the slots on
the touchpad and swing the touchpad bottom toward the
mounting plate. Gently tighten the screw into the bottom of the
touchpad.
Power up and Bus communication
After making all wiring connections from the touchpad to the
panel, you are ready to power up the panel and verify correct
communication between the touchpad and the panel. Upon
power up, the panel scans the bus for connected devices,
assigns a unit number to each bus device, and automatically
learns the device ID number of each bus device.
Ge Security 60–983 Atp1000 Alphanumeric Touchpad User Manual Software
1. Verify that all wiring between the panel and touchpad is
correct.
2. Connect the panel battery and restore AC power.
Alphanumeric touchpads briefly show SCANNING BUS
Ge Security 60–983 Atp1000 Alphanumeric Touchpad User Manual Template
DEVICES, then display date and time.
Note: Steps 3 through 9 are optional.
3. At the touchpad, enter program mode by pressing 8 +
installer/dealer code (default = 4321) + 0 + 0. The
touchpad should display SYSTEM PROGRAMMING.
4. Press É and the display shows SECURITY.
5. Press A or B until the display shows ACCESSORY
MODULES, then press É. The display should read BUS
DEVICES.
6. Press É. The display shows the lowest device address
and its ID. The following example shows what a device
address display may look like:
UNIT — ID
0–02110185*
*The 8-digit SuperBus ID number is also located on a label
on back of the touchpad.
7. Press A or B to cycle through all bus device addresses
until the touchpad appears.
8. After verifying the touchpad device ID, press Ç repeatedly
until the display shows SYSTEM PROGRAMMING.
9. Press A or B until the display shows EXIT
PROGRAMMING READY, then press É. The touchpad
should show the date and time display.
Programming
To program options for the newly installed touchpad (such as
key beeps) see the specific panel installation instructions.
2
ATP1000 Touchpad/Display Installation Instructions
Advertising
Popular Brands
Popular manuals
